This weathering
powder will adhere to any non-glossy
surface. It is NOT chalk. One quick step
gives a very
realistic rusty, dusty or
sooty surface - instantly. No drying or
curing is necessary. Use sparingly; a
little goes
a long way. This product is
made from real rust and other weathering
agents that have been ball milled to a
particle size over 100 times finer than
chalk and blended with a pressure
sensitive, dry adhesive. Self
adhesive
to most surfaces. Nonmagnetic and
Nontoxic. |
|
 |
 |
Four Color Set (1/2 oz.) $16.00
Ea.
004-FF60
Soot, Dk. Rust, Med. Rust, Lt.
Rust
004-FF161
Grimy Gray, Ash, Weathered Brown, Dust
Bowl Brown
004-FF162
Green Grunge, Old Yeller, Used Brick,
The Blues
004-FF163
Mortar White, Dk. Rail Brown, Antique
iron, Old Tuscan |
Large Single Color (2
oz.) $7.00 Ea.
004-FF61 Light Rust
004-FF62 Medium Rust
004-FF63 Dark Rust
004-FF64 Soot
004-FF66 Dust Bowl Brown
004-FF67 Grimy Gray
004-FF68 Ash
004-FF69 weathered Brown
004-FF267 Used Brick
004-FF269 Dark Rail Brown
004-FF270 Old Tuscan
004-FF271 Antique Iron |
|
|
 |
|
Truck Tuner |
|
030-82838 $11.95 |
|
The Truck
Tuner reconditions your HO gauge
railroad truck bearings so cars
roll smoother with less friction. Simply
insert the tool in place of a wheelset
and rotate the shank. Truck Tuner's
extra-sharp tool-steel cutter reshapes
the
bearing to the NMRA's recommended 60
degree contour and cleans out burrs
and grime. Repeat for all bearings and
your car is ready to really roll.
Increases train lengths that locomotives
can pull by up to 20%!
For HO standard gauge trucks only. |
|
|
High
Precision Micro Pin Vise |
|
030-15115 $10.95 |
|
Use this pin
vise for holding drill bits, reamers,
needle files, screws, taps, wires...even
pins. An
exceptionally well made tool from
Switzerland. Holds
micro-size drill bits up to no. 61 (.039
inch). Can be
used by hand or locked in a drill press.
This tool is
ideal for holding the small bits such as
#78, 79 & 80.
Made of nickel plated solid brass. 2
inches long
overall. |
|
|
 |
|
Magnetic
Gluing Jig |
|
030-60304 $29.95 |
| 10-1/4
inch x 10-1/4 inch, 21 gauge steel plate
with 7/8 inch flanges bent up at 90
degrees. Includes 8 magnetic holding
plates that keep components together
squarely while glue dries. |
|
|
 |
|
Thin Beam
Square 5" |
|
030-83261 $16.95 |
Use the
Thin Beam Square to mark and cut thin
wood and plastic.
The extra-thin profile of the beam
allows the blade to stay in close
contact with the surface of the piece,
so scribe lines and knife cuts
are super accurate. Works on stock up to
4 inches wide and as
thin as 1/16 inch. Made of ground steel
to precise specifications. |
|
|
 |
|
End Of Train
Device With Bright Red Flashing Light |
-
HO Scale, Ready to
Run, No Wiring Required
-
DCC or Analog
Compatible
-
Continuous Operation
with DCC
-
Exceptional Detail
including Antenna, Carry Handle, Red
Reflector, and More
-
Prototypically
Accurate Size
-
Prototypically
Accurate Flash Rate and Time
-
Low Rolling Friction
for an Electrical Pick-Up Design
-
No Batteries Required
-
Fits Most Train Cars
-
Integrated
Electronics
-
#5 Coupler Included
-
Black Metal Wheels
-
Made in USA
-
Available with 33"
and 36" Wheelsets, Regular or Long
Wires, Gray or Yellow Box - Specify
when ordering.
-
Matching Truck
Available: 33" 089-TRK33 or 36"
089-EOT36 $5.45 each.
|
|
|
 |
|
Faller Super
Expert Cement |
|
272-170490 $7.50 |
This is
an excellent cement for plastic that
provides quick, strong
bonds and features a special hollow
needle and protective cap. |
|
|
 |
|
Ambroid
ProWeld |
|
012-110
$4.99 |
-
Water-clear plastic fusing adhesive.
-
Dissolves a thin layer of each
surface to form a welded joint
-
Creates fast, neat, positive and
permanent bonds on ABS, Styrene,
Butyrate and Acrylic plastics.
- Its
unique "low surface tension" formula
assures speedy absorption into the
joint, resulting in superior bonds.
|
|
|
